A split system leaking water inside is usually a blocked drain line or a dirty drain tray, and a professional clean fixes that. Leaks from low refrigerant, a poorly sloped installation or a cracked tray need a licensed technician. Switch the unit off at the wall, and call us if it looks like a dirty drain.
Why is my split system leaking water inside the house?
The most common cause is a blocked condensate drain line. Your split system pulls moisture out of the air, collects it in a drain tray and sends it outside through a small pipe. When dust or slime blocks that pipe, the water backs up and spills from the indoor unit.
More detail
A blocked drain line is the usual suspect, but several other faults produce the same puddle under the unit:
- Blocked drain line: dust, slime and debris narrow the pipe until water has nowhere to go.
- Dirty or overflowing drain tray: the tray under the coil holds water between cycles, and a layer of build-up makes it overflow.
- Loaded filter or dirty coil: restricted airflow can make the coil freeze, then the ice melts faster than the tray can handle.
- Low refrigerant: this can also freeze the coil. It is a licensed technician job.
- Installation slope or fitting fault: if the drain line does not fall away from the unit, water sits or runs back.
- Cracked or damaged tray: water escapes before it reaches the drain.
A drip often comes with a sour smell, because the same wet, dirty parts feed mould. See why an air conditioner smells musty if you notice both.
How do I tell if it is a blocked drain line or something else?
Look at where and when it drips. A steady trickle from the bottom or front of the indoor unit while cooling, with no ice and normal airflow, points to a blocked drain. Ice on the coil or pipes, weak airflow or a hissing sound points to a different fault.
| What you see | Likely cause | Who fixes it |
|---|---|---|
| Steady drip or trickle from the bottom or front, no ice, normal airflow | Blocked drain line or dirty drain tray | Drain tray clean and drain line flush |
| Ice or frost on the indoor coil or pipes, weak airflow | Dirty filter or coil restricting airflow, or low refrigerant | Clean for the dirt, licensed technician for refrigerant |
| Leak since the day it was installed | Drain line slope or fitting fault | Licensed installer |
| Water from a clean, unblocked unit, or a visible crack in the tray | Damaged drain tray | Licensed technician |
| Wet or dripping refrigerant pipes along the wall | Damaged pipe insulation | Licensed technician or installer |
More detail
Two quick checks narrow it down. First, look at the outdoor end of the drain line while the unit cools. If water is leaking inside but nothing comes out outside, the line is probably blocked. Second, check whether the leak started after a long stretch without a clean. Dirt-related leaks tend to build up over a season, while installation faults show up early and keep repeating.
One honest limit: from inside the house you cannot see the slope of the drain line or the refrigerant level, so a table can only point you in a direction. The free inspection on every visit looks at the outdoor unit and the insulation on the refrigerant pipes in the house, and if it turns up a fault we do not fix, we tell you plainly.
Is water dripping from the outdoor unit normal?
Often yes. The drain line from the indoor unit usually ends outside, so a trickle there while cooling is normal condensate leaving the house. In heating mode the outdoor unit also melts frost and sheds water during defrost. Constant heavy dripping, or a leak inside with a dry outlet outside, needs a check.
More detail
Water outside is a sign the drain is doing its job. Water inside with nothing coming out outside is the pattern that points to a blockage. If the outdoor drain outlet is clear of leaves and mud and the unit still leaks indoors, the blockage is further up the line or the fault is elsewhere.
Can I unblock the aircon drain line myself?
You can wash the filters and look at the outdoor drain outlet for a visible blockage, but stop there. Forcing tools, pressure or chemicals into the line can push a blockage deeper or damage the unit.
More detail
- Switch the unit off at the wall before you touch anything, and put towels or a bucket under the leak.
- Slide out the filters, rinse them in lukewarm water with a little mild detergent and let them dry fully in the shade before refitting.
- Check the outdoor end of the drain line for leaves, mud or insects, and clear only what you can see and reach by hand.
- Leave the panels, the tray and the pipework alone. Water near the electrical parts inside the unit is a safety risk.
If the leak continues after that, the blockage is inside the unit or the line, which is where a professional clean comes in.
Describe where it drips and we will tell you whether a clean should fix it. Our Sydney team answers 24/7.
Does a professional clean fix a leaking split system?
It fixes leaks caused by dirt: a blocked drain line, a grimy drain tray, a loaded filter or a dirty coil. We clean the drain tray and flush the drain line as part of every split system cleaning. It does not fix refrigerant, slope or cracked-tray faults.
More detail
On a split system clean, the front cover and filters come off and a waterproof cover is fitted so no water runs down your wall. The evaporator coil is cleaned from both sides as far as access allows, the blower fan drum is removed and cleaned where possible, the drain tray is cleaned, the drain line is flushed, and the filters are washed and refitted. Water, mould and dust drain into a bucket we empty, and you get before and after photos.
We clean and sanitise aircon. We do not regas or repair units, so we never promise to fix a refrigerant leak or an installation slope. The free inspection on every visit covers the outdoor unit and the refrigerant pipe insulation, and any extra work we find is quoted on the spot and only done once you approve it. For how often to repeat the clean, see how often to clean your air conditioner in Sydney.
When should I turn it off and call a licensed technician?
Switch it off at the wall straight away if water is near power points or electrical items, if you see ice on the coil, hear hissing or smell burning. Call a licensed technician for refrigerant, electrical and installation faults. Call us when the cause looks like a dirty drain.
More detail
- Water near electrics: stop the unit and keep clear until it is dry and checked.
- Ice, hissing or a leak that returns after a clean: the cause is probably refrigerant or the installation, so a licensed technician needs to look at it.
- Burning smell or tripping safety switch: turn it off and get an electrician or licensed technician.
- Still running a leaking unit: water can soak the wall or ceiling below the unit, so mop up and keep the unit off until the cause is found.
How do I stop it leaking again?
Wash the filters every 1 to 3 months in heavy use and book a professional clean once a year for most Sydney homes, so slime never builds up in the drain tray and line. Keep the outdoor drain outlet clear and act on the first drip.
More detail
Leaks rarely arrive without warning. A damp patch under the unit, a sour smell or weaker airflow usually comes first, so it pays to know the signs a split system needs cleaning. Running the fan for a few minutes after cooling can help the coil dry out, and keeping the filters clean keeps air moving across the coil so it does not ice up.